Monitor Parts
Parts Diagram 6 Tiller Attachment Kit
Parts Diagram 7 Wheel Adapter Complete
Parts List
| Part No. | Part | Qty. in a Monitor | Qty. in Cruising Parts Kit | Price |
|---|---|---|---|---|
| T2 | Single stainless steel casting - for Swing-Gate or SOS Rudder | $165.00 | ||
| T3 | Double stainless steel casting - for Swing-Gate or SOS Rudder | $209.00 | ||
| 1 | Small (blue) airvane | $55.00 | ||
| 1.1 | Large (red) airvane | $75.00 | ||
| 2 | Bearing cone | 2 | $16.00 | |
| 3 | Bearing set (36 bearings per set) | 1 | $5.00 | |
| 4 | Bearing race | 2 | $18.00 | |
| 5 | Airvane weldment | $295.00 | ||
| 6 | Airvane shaft | $29.00 | ||
| 7.2 | Washer, 1/2" | $0.75 | ||
| 7.4 | 1/2"-20 Nylock nut | $2.00 | ||
| 8 | Airvane yoke | $295.00 | ||
| 9.2 | Flanged bearing, Delrin .077" (thin) | $19.00 | ||
| 9.3 | NO LONGER AVAILABLE | $0.00 | ||
| 10.2 | Washer, Delrin .110" (thin) | $16.00 | ||
| 10.3 | Washer, Delrin .115" (thick) | $16.00 | ||
| 11 | Airvane base | $195.00 | ||
| 12 | Screw, 10-32 x 1/2" | 2 | 1 | $0.50 |
| 13 | Lockwasher, #10 | 7 | 2 | $0.20 |
| 14 | Nut, 10-32 | 2 | 2 | $0.50 |
| 15 | Pilot shaft bushing | 2 | 2 | $0.75 |
| 16 | Pilot shaft plate | $9.00 | ||
| 17 | Washer, 5/16" (thin) | 2 | 2 | $0.25 |
| 18 | Pilot shaft chain | $99.00 | ||
| 19 | Pilot shaft sprocket | 1 | $15.00 | |
| 20 | Pilot shaft, including small sprocket | $144.00 | ||
| 20.3 | Cap plug | 1 | $0.25 | |
| 21 | Spyrolock ring, 3-1/2 | 1 | $19.00 | |
| 25 | Pilot shaft spring | 1 | $6.00 | |
| 26 | Pendulum strut | $430.00 | ||
| 26.2 | Bearing cup (to be welded on) | $16.00 | ||
| 26.6 | Yoke bearing collar (to be welded on) (2 total in unit) | 2 | $31.00 | |
| 29.1 | SS washer, .008" (thin) | 2 | $1.75 | |
| 29.2 | SS washer, .030" (medium) | 1 | $1.75 | |
| 29.3 | SS washer, .098" (thick) | $1.75 | ||
| 31 | Roller bearing set (80 bearings per set) | 1 | $16.00 | |
| 32 | Set screw, 10-32 x 3/8" (for watervane support shaft) | 2 | 2 | $0.75 |
| 32.1 | Set Screw, 10-32 x 1/2" (for hinge) | 1 | $0.75 | |
| 33 | Watervane support shaft | $38.00 | ||
| 34 | Flanged shaft bearing | 2 | 2 | $5.00 |
| 36 | Pinion gear | $274.00 | ||
| 37 | Ring gear | $274.00 | ||
| 38 | Flat washer, 1/4" | 1 | $0.25 | |
| 38.1 | Oval-head machine sScrew, 1/4"-20 x 2" | 1 | $2.50 | |
| 40 | Large airvane control sprocket | $64.00 | ||
| 41 | Washer, 1-1/4 | 2 | 2 | $6.00 |
| 42.1 | Washer, 1-1/4" SS, .015" (thin) | 1 | $4.50 | |
| 42.2 | Washer, 1-1/4" SS, .030" (medium) | 1 | $4.50 | |
| 43 | Watervane pivot shaft | $395.00 | ||
| 44 | Hinge | $355.00 | ||
| 44.7 | 5/16"-18 x 2-1/2" bolt for hinge to safety tube | $2.50 | ||
| 46 | Latch trip line, 5' | $4.50 | ||
| 47 | Latch | $98.00 | ||
| 48 | Latch spring | 1 | $18.00 | |
| 49 | Roller sheave block in-frame (4 total in unit) complete | 4 | 1 | $49.00 |
| 52 | Cap screw, 1/4"-20 x 1" | 2 | 2 | $1.25 |
| 52.1 | Cap Screw, 1/4"-20 x 1-1/4" | 2 | 2 | $1.25 |
| 52.2 | Nylock nut, 1/4"-20 | 4 | 3 | $1.25 |
| 54 | Actuator shaft bearing | 2 | 2 | $18.00 |
| 55 | Retainer ring, 3/8" beryllium copper | 3 | 6 | $1.50 |
| 56 | Actuator nut, 1/2"-20 | $1.75 | ||
| 57 | Actuator shaft | $165.00 | ||
| 58 | Main frame | $1495.00 | ||
| 59 | Socket button-head machine screw, 5/16"-18 x 1/2" | 2 | 1 | $3.50 |
| 60 | Socket flat-head machine screw, 5/16"-18 x 1/2" | 1 | $3.50 | |
| 61 | Water paddle (includes 10' of 1/4 | $625.00 | ||
| 61.9 | NO LONGER AVAILABLE | 3 | $0.00 | |
| 63 | 5/16" lockwasher | 3 | 4 | $0.25 |
| 64 | 5/16"-18 hex nut | 3 | 4 | $0.50 |
| 64.1 | 5/16"-18 Nylock nut for safety tube bolt | 1 | $0.75 | |
| 66 | Watervane safety line, 1/4" x 10' length | $17.50 | ||
| 67.1 | Safety tube (.049 | $48.00 | ||
| 67.2 | Safety Tube (.065 | $58.00 | ||
| 68 | Airvane clamp knob | 2 | 1 | $9.00 |
| 69 | Tiller chain for old-style tiller attachment | $30.00 | ||
| 70 | Tiller plate for old-style tiller attachment | $50.00 | ||
| 71 | Tiller U-bolt rod for old-style tiller attachment | 2 | $12.00 | |
| 71.2 | 10-32 nut for old-style tiller attachment | 4 | $0.25 | |
| 71.3 | Lockwasher, #10 for old-style tiller attachment | 4 | $0.10 | |
| 72 | 10-32 X 1" Philip machine screw, lockwasher & nut | 1 | $2.50 | |
| 74 | Actuator shaft bushing (2 total in unit) | 2 | 2 | $9.00 |
| 75 | Actuator shaft washer, SS | 5 | 2 | $0.50 |
| 76 | Hinge pin - single hole for cotter pin | 1 | $18.00 | |
| 76.1 | Tapered hinge pin - two holes for retaining rings | $29.00 | ||
| 76.2 | Hinge pin retaining ring | 2 | 2 | $1.50 |
| 77 | 10-24 X 3/4" Philip machine screw | 3 | $0.75 | |
| 78 | Airvane clamp | $19.00 | ||
| 79 | Pulley, delrin | $59.00 | ||
| 80 | Threaded actuator shaft clevis | $59.00 | ||
| 81 | Plain actuator shaft clevis | $55.00 | ||
| 82 | End fitting (2 or 4 total in most units) | $38.00 | ||
| 83.2 | Upper U-bracket (2 total in unit) including 316L SS mounting hardware | $65.00 | ||
| 83.4 | Lower U-bracket (2 total in most units) including 316L SS mounting hardware | $60.00 | ||
| 84 | Old-style L-bracket (2 needed per tube) including 316L SS mounting hardware | $29.00 | ||
| 84.3 | 5/16"-18 x 2" bolt for paddle to safety tube | $2.50 | ||
| 84.32 | 5/16-18 x 2-2/4 bolt for upper mounting tube socket w/diagonal tube | $2.50 | ||
| 84.4 | 5/16" -18 x 3" mounting bolt | $2.50 | ||
| 84.5 | 5/16"-18 x 2" all-thread bolt | 2 | $3.00 | |
| 84.6 | 5/16"-18 x 5" all-thread bolt | $6.00 | ||
| 84.7 | 5/16"-18 x 6" all-thread bolt | $8.00 | ||
| 84.8 | 5/16"-18 x 8" all-thread bolt | $10.00 | ||
| 84.9 | 5/16" fender washer | 2 | $1.50 | |
| 85.1 | Compression tube insert (1.9") | 2 | $4.00 | |
| 85.2 | Compression tube insert (1.25") | $3.00 | ||
| 86.1 | 5/16"-18 x 1" bolt with 3/32" hole for sfety wire (included) (2 total in unit) | 2 | 2 | $7.00 |
| 87 | Turning block bracket | 2 | $44.00 | |
| 88.1 | Lower tubing (1.25" x .049" wall) per inch | $3.00 | ||
| 88.2 | Diagonal tubing (one end flattened & drilled) (1.25" x .049" wall) per inch | $3.00 | ||
| 89.1 | Upper tubing (1.9" x .049" wall) per inch | $4.00 | ||
| 89.2 | Upper tubing (1.9" x .065" wall, required for bends over 15 degrees) per inch | $4.50 | ||
| 89.3 | Upper mounting tube tab bracket | $49.00 | ||
| 90 | Tube bending, per bend | $30.00 | ||
| 101 | Wheel adapter drum | $265.00 | ||
| 102 | Wheel adapter disk with angle bracket, barrel and pin | $225.00 | ||
| 103 | Barrel for pin | $59.00 | ||
| 104.1 | Angle bracket for pin & barrel (to be welded on) | $17.00 | ||
| 107 | Pin | $16.00 | ||
| 108 | Wheel drum line grommet | 2 | $1.50 | |
| 109 | Spyrolock ring for wheel adapter | $19.00 | ||
| 110.1 | Flanged bearing for wheel adapter, .121" wall (thick) | $16.95 | ||
| 110.2 | Flanged bearing for wheel adapter, .111" wall (medium & most common) | $16.95 | ||
| 110.3 | Flanged bearing for wheel adapter, .101" wall (thin) | $16.95 | ||
| 111 | SS hose clamp | $2.00 | ||
| 112 | Wheel adapter line, 1/4" - two 6' lengths | $22.00 | ||
| 114.2 | NO LONGER AVAILABLE | $0.00 | ||
| 114.3 | Spacer bearing, .020" (thin) | $4.00 | ||
| 115 | Pin spring | $5.00 | ||
| 117 | Wood dowel for support shaft (used for rebuilding) | 1 | $1.50 | |
| 820 | Pendulum lines - 1/4" custom Spectra line, per foot | $1.75 | ||
| 820.1 | Pendulum Line set, standard length - two 18' lengths - for aft cockpit | $50.00 | ||
Assemblies & Kits | ||||
| $0.00 | ||||
| 100 | Wheel adapter complete | $575.00 | ||
| 120 | Wheel adapter rebuild kit | 1 | $42.00 | |
| 180 | NO LONGER VALID | $0.00 | ||
| 181 | NO LONGER VALID | $0.00 | ||
| 420 | Block assembly complete with sheave, external (2 total in unit) | 2 | $59.00 | |
| 440 | Hinge/latch assembly - includes parts 44, 46, 47, 48, 76, 76.1, 76.2(3) & 5' release line) | $525.00 | ||
| 501 | Airvane weldment assembly - includes parts 2, 3 ,4, 5, 6, 7.2, 7.4, 8, 9, 10, 11, 21 and 40 | $995.00 | ||
| 570 | Actuator shaft complete - includes parts 55, 56, 57, 74(2), 75, 80 and 81 | $289.00 | ||
| 601 | Watervane/hinge assembly - includes parts 440, 61, 66 & 67 and bolts & nuts as needed | $1260.00 | ||
| 701 | Tiller attachment kit - new-style - cam cleats | $60.00 | ||
| 701.1 | Tiller attachment kit - old-style - includes parts 69,70,71(2),71.2(4), and 71.3(4) | $75.00 | ||
| 801 | Cruising parts kit (see column at right for contents) | $195.00 | ||
| 810 | Bearing kit - includes parts 3, 9, 10, 15(2), 31, 34(2), 41(2), 54(2), 55(6) & 74(2) and 117 | $145.00 | ||
| 815 | Block kit - includes parts 49(4), 420(2), 52(2), 52.1(2) and 52.2(4) | $295.00 | ||
| 825 | Airvane kit - includes parts 1(small) and 1.1(large) | $110.00 | ||
| 831 | Add strut guard (for pre-October 1991 units) | $165.00 | ||
| 840 | M-Rud - Emergency rudder system complete with hinge assembly | $1495.00 | ||
| 841 | M-Rud - Emergency rudder system without hinge assembly | $1195.00 | ||
| 845 | M-Rud - Pendulum support bracket only | $295.00 | ||
| 850 | Westsail 32 boomkin mount - complete set | $475.00 | ||
| 851 | Westsail 32 - upper mounting tubes only | $320.00 | ||
| 851 | Westsail 32 boomkin mount - upper tubes only | $320.00 | ||
| 900 | Shipping box | $40.00 | ||
| 901 | Monitor manual, including parts diagram and parts price list | $20.00 | ||
| 950 | Westsail 32 mount - complete set | $450.00 | ||
Labor | ||||
| 180 | Basic wheel adapter rebuild (108, 110, 112, 114) | $150.00 | ||
| 181 | Add new pin & barrel to wheel adapter (103,104, 107, 115) | $125.00 | ||
| 1006 | Shop labor rate (including welding), per hour | $100.00 | ||
| 830 | Monitor Rebuild--This includes complete disassembly, inspection, replacement of all bearings, corrosion treatment, new pendulum lines, reassembly, and final inspection. This DOES NOT include the replacement of worn parts other than bearings. An estimate of parts that need to be replaced will be provided to each customer as required after the initial factory inspection. Please call to obtain a rebuild authorization number prior to sending your Monitor to the factory. This will speed up the turnaround production time. All old parts will be returned with the rebuild upon your request. | $1095.00 | ||






